CISCO AIRONET 1130AG MANUAL PDF

Quick Links. Download this manual. Table of Contents. Read This First. You should review this table and the instructions for opening the top cover.

Author:Zululkree Yozshutilar
Country:Guadeloupe
Language:English (Spanish)
Genre:Science
Published (Last):19 February 2015
Pages:327
PDF File Size:3.76 Mb
ePub File Size:19.94 Mb
ISBN:234-4-22564-215-3
Downloads:60435
Price:Free* [*Free Regsitration Required]
Uploader:Voodooktilar



This chapter describes the installation of the access point and includes these sections:. Follow the guidelines in this section to ensure proper operation and safe use of the access point. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

Translated versions of the following safety warnings are provided in "Translated Safety Warnings. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative. Because the access point is a radio device, it is susceptible to interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:. Microwave ovens operate on the same frequency as the access point and can cause signal interference.

When mounted to such surfaces, the integrated antennas produce the best antenna radiation pattern. For advanced features such as voice, location, and rogue access point detection, ceiling mounting is strongly recommended.

However, for smaller areas such as conference rooms, kiosks, transportation, and hot-spot usage where the customer is concerned primarily with data coverage and not advanced features, this unit may be wall mounted using the supplied plastic wall anchors and 8 screws.

Cisco switches support a DHCP server option. The process of storing controller IP addresses in access points for later deployment is called priming the lightweight access point. You can also manually configure controller information using CLI commands on new out-of-the-box access points that are not connected to a controller. Cisco recommends that you configure a DHCP server with Option 43 to provide the controller IP addresses to your lightweight access points.

Cisco switches provide a DHCP server option that is typically used for this purpose. For lightweight access points, record the access point MAC address on the access point location map. When you have completed the access point deployment, return the access point MAC addresses and the access point locations on the access point location maps or floor plans to your network planner or manager. The network operators can use the MAC address and location information to create maps for precise wireless system management.

Attach your access point to the mounting plate see the "Attaching the Access Point to the Mounting Plate" section. Mount the access point at the indicated destination using the specified mounting method.

For specific mounting instructions, see these sections:. Optionally secure the access point using a padlock or security cable see the "Securing the Access Point" section. Connect the access point cables Ethernet, optional power, optional antennas. For instructions see the "Connecting the Ethernet and Power Cables" section. On power up, verify that the access point is associated to a controller and operating normally.

A master controller should only be used for configuring access points and not in a working network. Note There is a second keyhole slot located on the bottom of the unit near the security slot. The access point mounting plate is designed to accomodate multiple mounting methods.

The mounting holes on the plate are marked so that you can easily identify the correct holes for a specific mounting method. You can use the mounting plate as a template to mark the locations for the cable hole and the mounting holes for your installation.

The keyhole clips slide into the keyhole slots on the bottom of the access point. The mounting kit contains two 8 x 32 x 1 inch pan head screws and wall anchors for wall or ceiling mounting. Compatible padlocks are Master Lock models T and T or equivalent.

The security hasp adapter can also be used with the padlock for increase security protection. Note The security hasp covers the cable bay area including the power port, Ethernet port, console port, and the mode button to prevent the installation or removal of the cables or the activation of the mode button. The accessory kit contains one suspended ceiling adjustable T-rail clip that can be used for standard and recessed ceiling tile rails.

The clip is adjustable to accomodate three standard T-rail widths. The clip contains detents that are used to adjust the clip to the T-rail. Each detent contains markings that indicate the T-rail width and the hole letter that corresponds to the correct mounting holes on the mounting plate.

The top cover provides access to the cable bay area containing the power connector, Ethernet port, console serial port, the mode button, and the Ethernet and Radio LEDs. The cover is designed to partially open by sliding back from a secured position. Follow these steps to open the top cover:. You will need to supply the appropriate wall anchors and fasteners to mount your access point.

Follow these steps to mount the access point on a horizontal surface:. To attach the access point to the mounting plate, see "Attaching the Access Point to the Mounting Plate" section. The access point mounting bracket is designed to be integrated into the T-bar grid above the tiles of a suspended ceiling.

You may need to modify a thicker tile to allow room for the access point. Follow these steps to mount the access point above a suspended ceiling. See the illustration above. Make sure the clips are securely attached to the T-rails. This additional support is required in order to comply with the U. National Electrical Safety Code.

To attach the access point to the mounting plate, see the "Attaching the Access Point to the Mounting Plate" section. When placing the access point on a desktop of shelf, you do not need the mounting plate. The access point has four rubber pads on the bottom to help prevent sliding or scratching the surface of your desktop or shelf. For information on connecting the access point cables, see the "Connecting the Ethernet and Power Cables" section.

You will hear a click when the locking detent contacts the access point and locks it into place. For instructions on connecting your cables, refer to the "Connecting the Ethernet and Power Cables" section. For instructions on securing your access point, refer to the "Securing the Access Point" section. The security cable can be used with any of the mounting methods described in this guide. The mounting plate provides two methods of securing your access point to restrict its removal:. Compatible padlocks are Master Lock models T or T.

Note The security hasp adapter covers the cable bay area including the power port, Ethernet port, console port, and the mode button to prevent the installation or removal of the cables or the activation of the mode button. Note Using a tamper-resistant head screw to secure the access point to the mounting plate does not prevent someone from inserting or removing the access point cables or pressing the mode button. The access point receives power through the Ethernet cable or an external power module.

Note Some older switches and patch panels might not provide enough power to operate the access point. At power-up, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition.

Note If your access point is connected to in-line power, do not connect the power module to the access point. Using two power sources on the access point might cause the access point to shut down to protect internal components and might cause the switch to shut down the port to which the access point is connected.

If your access point shuts down, you must remove all power and reconnect only a single power source. Follow these steps to connect the access point to the Ethernet LAN when you have an inline power source:. Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source:.

For information on securing your access point, see the "Securing the Access Point" section. The Cisco logo on the top of the unit can be rotated to correctly position the logo for any mounting arrangement making it always easy to read.

Detents are provided to help you align the logo for 90 degree rotations. Skip to content Skip to footer. Book Contents Book Contents. Find Matches in This Book. PDF - Complete Book 2. Updated: October 19, Chapter: Installing the Access Point. Warnings Translated versions of the following safety warnings are provided in "Translated Safety Warnings.

You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement Warning This product relies on the building's installation for short-circuit overcurrent protection.

Ensure that the protective device is rated not greater than: 20A Statement Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. For specific mounting instructions, see these sections: — Horizontal surface, such as a ceiling see the "Mounting the Access Point on a Horizontal Surface" section. Mounting Plate The access point mounting plate is designed to accomodate multiple mounting methods.

Suspended Ceiling Adjustable T-Rail Clip The accessory kit contains one suspended ceiling adjustable T-rail clip that can be used for standard and recessed ceiling tile rails.

Caution Do not attempt to pry open or lift the top cover of the access point because you could damage the cover. Carefully read the instructions in this section before attempting to open the access point cover. Mounting the Access Point on a Horizontal Surface Caution Avoid mounting the access point on a wall or vertical surface because the metal plate on the unit designed to dissapate heat acts as a reflector, causing the access point's integrated antenna to propagate directionally.

The directional propagation can result in reduced performance, especially when using advanced features such as voice or location. Mounting the Access Point Above a Suspended Ceiling The access point mounting bracket is designed to be integrated into the T-bar grid above the tiles of a suspended ceiling.

Caution Cisco does not sell Ethernet cable rated for use in a building environmental air space, such as above suspended ceilings.

You must obtain special Ethernet cable with the appropriate rating.

BIOESTADISTICA AMIGABLE PDF

Cisco Aironet 1130AG Quick Start Manual

This chapter describes the installation of the access point and includes these sections:. Follow the guidelines in this section to ensure proper operation and safe use of the access point. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits. Translated versions of the following safety warnings are provided in "Translated Safety Warnings.

ASTRAL PLANE ITS SCENERY INHABITANTS PHENOMENA PDF

Cisco Aironet 1131AG AIR-LAP1131AG-E-K9 Data Sheet

Note If you purchased an G access point, this quick start guide refers occasionally to an However, your G access point does not contain an Please disregard the sections in your quick start guide that refer specifically to an You should review this table and the instructions for opening the top cover. The table contains important information you need to know so you can successfully configure your access point. Cisco case sensitive. Determined by DHCP server.

ENESCO CANTABILE ET PRESTO PDF

Cisco Aironet 1131G - Radio access point AIR-LAP1131G-E-K9 User Manual

.

LEGO 6375 PDF

Cisco Aironet 1130AG Hardware Installation Manual

.

Related Articles