MAKITA LS1040 MANUAL PDF

You'll find. Detailed instructions for use are in the User 's Guide. Turn off tool and wait for saw blade to stop before moving workpiece or changing settings. Always secure all moving portions before carrying the tool.

Author:Mikagul Doubei
Country:Albania
Language:English (Spanish)
Genre:Technology
Published (Last):15 August 2014
Pages:385
PDF File Size:7.62 Mb
ePub File Size:4.16 Mb
ISBN:531-8-15646-531-7
Downloads:32250
Price:Free* [*Free Regsitration Required]
Uploader:Taujora



Quick Links. See also: Instruction Manual. Table of Contents. Compound Miter Saw. Equipped with Electric Blade Brake. Miter angle Bevel angle Page 3 5. Keep work area well lighted. If you use this tool unsafely or incorrectly, you can suffer seri- ous personal injury. Page 5 Make sure that the turn base is properly secured so it will not move during opera- tion.

Use the holes in the base to fasten the saw to a stable work platform or bench. NEVER use tool where operator positioning would be awkward. Auxiliary plate 2. Hex bolt 3. Base 1. Base 3. Hex bolt 4. Nut 1. Stopper pin 1. Page 8: Blade Guard Do not remove spring holding blade guard. If guard becomes discolored through age or UV light exposure, con- tact a Makita service center for a new guard. When installing a new blade, always check the lower limit position of the blade and if necessary, adjust it as follows: First, unplug the tool.

Page Adjusting Bevel Angle To adjust the bevel angle, loosen the lever at the rear of the tool counterclockwise. Push the handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel scale. Then tighten the lever clockwise firmly to secure the arm.

Page 12 3. Blade guard 1. Socket wrench 2. Shaft lock 1. Hex bolt 2. Outer flange 3. Saw blade 4. Inner flange 5. Spindle 1. Blade case 2. Arrow 3. Arrow To remove the blade, use the socket wrench to loosen the hex bolt holding the center cover by turning it counterclock- wise.

Page Horizontal Vise 1. Sub-fence 1. Vise arm 2. Vise rod 3. Guide fence 4. Holder 5. Holder assembly 6. Vise knob 7. Screw 1.

Vise knob 2. Projection 3. Vise shaft 4. Page Holders And Holder Assembly 1. Holder 2. Holder assembly 1. Holder assembly 2. In this case, turn the vise knob back counterclockwise until the screw is released, before turning again gently clockwise. Be sure to retighten the lever firmly to secure the selected bevel angle safely. Page 17 5. Cutting crown and cove moldings Crown and cove moldings can be cut on a compound miter saw with the moldings laid flat on the turn base.

Page 18 When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table A and position the moldings on the top surface of the saw base as indicated in the table B. Page 19 Page 20 Page 21 4. Aluminum extrusion 5. Spacer block Crown molding stoppers optional accessories allow easier cuts of crown molding without tilting the saw blade.

Install them on the base as shown in the figures. Page 22 1. Set plate 2. Holder 3. The screws should be installed so that the screw heads are below the surface of the wood facing. Page Carrying Tool 1. Hex bolt Carrying tool Make sure that the tool is unplugged. Lower the handle fully and lock it in the lowered position by pushing in the stopper pin.

Page 24 1. Turn base 2. Lever 3. Hex nut 1. Triangular rule 2. Saw blade 3. Top surface of turn base 1. Arm 2. Bevel scale 3. Pointer 4. Turn base Lower the handle fully and lock it in the lowered position by pushing in the stopper pin. Page Replacing Carbon Brushes 10 minutes.

Then check the tool while running and electric brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair. The use of any other accessories or attachments might present a risk of injury to persons.

Only use accessory or attachment for its stated purpose. Page 27 Memo Page 28 Memo Makita U. Page 30 Paste 3. Be sure to attach a letter to the outside of Model No. Print page 1 Print document 32 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up!

THE GRAMMAR OF ENGLISH GRAMMARS BY GOOLD BROWN PDF

Makita LS1040 user manual

Quick Links. Download this manual See also: Instruction Manual. Table of Contents. Compound Miter Saw. Cutting capacities H x W with blade mm in diameter Page 3: Safety Instructions For Model LS The typical weighted root mean square acceleration For public low-voltage distribution systems of value is not more than 2. Page 4: Additional Safety Rules For Tool periodically and if damaged have it repaired by an that is damaged should be carefully checked to authorized service facility.

CALIGRAFIA TECNICA IRAM PDF

User manual MAKITA LS1040 - MY PDF MANUALS

Our goal is to provide you with a quick access to the content of the user manual for Makita LS Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Makita LS If looking through the Makita LS user manual directly on this website is not convenient for you, there are two possible solutions:. Many people prefer to read the documents not on the screen, but in the printed version.

APPRENDRE JOOMLA 1.5 LES FONDAMENTAUX PDF

Makita LS1040 Instruction Manual

.

FOTOTIPOS CUTANEOS PDF

Makita LS1040 Saw User Manual

.

Related Articles