Quick Links. Download this manual. Table of Contents. Page 3 Please feel free to contact our local office or company headquarters.

Author:Tar Vill
Language:English (Spanish)
Published (Last):3 February 2018
PDF File Size:3.23 Mb
ePub File Size:3.87 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual See also: User Manual. Free Communication, Wonderful Life. Table of Contents. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co.

Page 3 Do not dismantle the equipment by yourself. In case of failure, send the equipment to an authorized maintainer. Without prior written consent from Huawei, no company or individual is allowed to decompile, disassemble, modify or reverse engineer the equipment and shall be solely responsible for any effect resulted from such action. Page 4 While plugging or unplugging the cables, keep your hands dry and do not touch the metallic part of a cable.

Do not trample on, stretch, or over bend the equipment cables, to avoid equipment failure. Huawei Technologies Proprietary Page 5 Keep the power socket clean and dry, to avoid electric shock or other dangers.

Note: If the device is in use for a long time, temperature of the shell will go up. This is no exception and the device can work normally. Page 6: About This Manual Technical terms and abbreviations Abbreviations Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

Page 7: Table Of Contents 4. Page 8 4. Page 9 5. Page 10 2 this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE Internet connection is not established. Blinking Data is being transmitted. Page Chapter 2 Installation I. Disconnect the power — Make sure you turn off the power for the computer and HG Page 18 Please note that the cable supplied is the straight-through cable. Use crossover cable to connect HG and the uplink port of a switch or hub.

Be sure the device has to be stored, transported, and operated in a non-humid and dust-free environment. Be careful not to drop down the device. Configure the computer to obtain IP address automatically. Or you can configure the computer IP address to be in the same network segment as HG The default IP address of HG is Enter the IP address The dialog box of Figure will appear. Enter the user name and password. Both of them are admin by default as shown in Figure Page 22 Figure Authentication 3.

Click OK. After the authentication is completed, the browser will display the home page of HG as shown in Figure Page 23 The left side is the navigation tree of the operation interface. Click a hyperlink and the corresponding page will appear on the right. You can configure the services according to the prompts.

Note: If you have problems during configuration, contact your Internet service provider for help. Page Chapter 4 Configuring Hg Whenever you made a configuration, remember to save the changes and reboot so to activate the changes. Page Service Information 4. It also shows Huawei Technologies Proprietary Page 27 In terms of network transmission, full duplex refers to duplex receive and transmit packages simultaneously, while half duplex means only receive or transmit.

Status Show the Ethernet status. Page Traffic Statistics Show the protocol this device applies for connecting to the Internet. Click Renew to update the statistics. Single click Submit to complete the configurations. Lite mode also called as G. Single click the trashcan icon under the Actions to delete an existing PVC. Click Submit to activate the settings after you finish the setting up. All the settings will be activated only after you reboot HG Page 35 It is recommended that you configure as being assigned an automatic IP address.

Page 36 HG will use the factory default settings for operation. Generally speaking, the default connection and service modes will satisfy your demand. Page Lan Setting IP address and subnet mask.

Enter the proper IP address and subnet mask in the space as shown in Figure Click Submit to activate the configuration.

Page Dhcp Setting Lease time refers to the time frame that you are allowed to use the assigned IP address. You will have to file application for a new IP address once the lease time expires. With the configuration of such DMZ feature, the internal networks are more securely protected.

Page 44 80, local IP as Single click Submit button to save the settings. You have to reboot the device to activate the settings. Single click New button on Figure to create a new IP route. Enter the settings and single click Submit to complete the settings.

With RIP, routers periodically exchange entire tables. When you are done, single click Submit at the bottom of the page to save the changes. Page Ip Filter to port of IP address You can add you own rules based on actual needs. Enter the parameters and single click Submit to save the configurations. Page 54 Internet user can access the service provided on IP address Figure Multinat Setting Single click New button to open the configuration page.

Enter the internal and external IP addresses. Page Parental Control When done, single Submit to activate the settings and the controlled days of the week and blocking time will be shown as in Figure Single click Remove button to remove a group and add ungrouped interface to the default group. You can configure up to 16 entries. To remove a group, check the Remove box and click Remove. Note: The selected interfaces will be removed from the existing group and added to the new group.

Page Protocol Block Apart from the default protocols, there is a Customer Define option for you to add more protocols that you want to block. Select the protocols that you wish to block and click Submit to save the change. Page Configuring Security 1. Configure WEP keys. You can configure from 1 to four network keys. Page 62 Network Key. Therefore, the Radius server must be running before you enable Page 63 5. Follow the same instruction on 4. Shared WEP configuration to configure the four network keys.

It improves the data encryption through the Huawei Technologies Proprietary Page 64 1. Enable WPA. The default value is 0 no re-keying.


Huawei EchoLife HG520 User Manual



Huawei EchoLife-HG520i User Manual



Manual for Huawei EchoLife-HG520i Router




Related Articles